Building a retaining wall might look simple. Just stack the blocks and fill in behind them. But we have seen many walls fail within a few years due to mistakes that could have been easily avoided during installation.
These mistakes are common in Australian yards, whether you’re doing it yourself or hiring someone who cuts corners. If things go wrong, it’s not just about looks. You could face structural failure, soil movement, flooding, and repair costs much higher than the original build.
This blog looks at the seven most common mistakes people make when installing retaining wall blocks, along with what you should do instead.
Mistake 1: Skipping Proper Base Preparation
The most common reason retaining walls fail happens before you even lay the first block. If the base isn’t prepared properly, the rest of the wall won’t stay in place.
A lot of DIYers and inexperienced contractors just dig a shallow trench, put in the first row of blocks, and start building. But without a level, compacted base made from the right material and at the right depth, the wall can shift, lean, or sink over time.
What to do instead:
- Excavate to a depth of at least 100mm to 150mm below ground level for the first course
- Use compacted road base or crusher dust as your foundation material
- Check for level across the entire base before laying a single block
- In soft or unstable soils, go deeper and consider professional advice
The first course sets the direction of everything above it. Spend the extra time here, and the rest of the job becomes much easier.
Mistake 2: Poor or No Drainage Behind the Wall
This is likely the biggest reason retaining walls fail in Australia. Water is very heavy, and if it collects behind a wall with nowhere to go, the hydrostatic pressure can push over even a well-built wall.
Many people just backfill with the clay soil they dug out and think the job is finished. But clay holds water. Over time, especially after heavy rain in places like Queensland, New South Wales, and Victoria, the trapped water can build up significant pressure on the wall.
What to do instead:
- Always install drainage aggregate (20mm crushed rock or similar) directly behind the wall to a depth of at least 300mm
- Use a geotextile fabric between the drainage aggregate and the native soil to prevent fines from migrating through
- Install a slotted ag pipe at the base of the drainage zone and direct it to a suitable outlet
- Never use clay-heavy soil as backfill material directly against the wall
Getting drainage right is not optional. It’s what keeps the wall standing long term.
Mistake 3: Not Burying the First Course Enough
Visible ground level and actual structural ground level are two different things. A common mistake is starting the wall at ground level rather than burying a full course or more underground.
The buried course acts as the anchor for the entire wall. Without it, the base can slide forward, especially on slopes or where foot traffic or vehicles are nearby.
What to do instead:
- Bury at least one full course below finished ground level
- For taller walls, bury deeper. A rule of thumb is to bury 10% of the total wall height underground
- Ensure the buried course is fully seated on compacted base material
This step adds cost and labour, but it’s non-negotiable for walls that need to hold.
Mistake 4: Building Too High Without Engineering Input
In Australia, retaining walls over a certain height (typically 600mm to 1 metre, depending on your council) require engineering design and often a building permit. Many homeowners and even some tradies push past this threshold without any professional oversight.
Taller walls carry significantly more load. The soil pressure they need to resist increases dramatically with height. A wall built without proper design for a height it wasn’t intended to carry is a safety risk, not just an aesthetic problem.
What to do instead:
- Check with your local council before you start regarding height limits and permit requirements
- For walls over 1 metre, get a structural engineer to design or assess the wall
- Use block systems that are specifically rated for the intended height
- Factor in surcharge loads (driveways, structures, vehicles) that sit above the wall
Council requirements exist for good reason. Ignoring them can also create issues when you go to sell the property.
Mistake 5: Ignoring Wall Batter (the Lean)
Most retaining wall block systems are designed to be installed with a slight batter, meaning the wall leans back into the slope slightly rather than sitting perfectly vertical. This lean helps the wall resist the soil pressure behind it.
A common mistake is building walls that are dead vertical or even leaning forward. This dramatically reduces the wall’s ability to handle the load behind it and accelerates failure.
What to do instead:
- Follow the manufacturer’s specifications for your block system’s recommended batter angle
- Most systems have a setback per course built into the block design. Use it
- Check your batter with a spirit level and string line as you go, not just at the end
A properly battered wall is a stronger wall. It’s built into the product’s engineering for a reason.
Mistake 6: Using the Wrong Backfill Material
What goes behind the wall matters as much as the wall itself. Using excavated clay soil or construction fill as backfill is a mistake that causes problems in two ways: poor drainage (as covered earlier) and differential settlement, which causes uneven pressure and cracking.
Heavy, expansive soils also swell when wet and contract when dry, creating ongoing pressure cycles that constantly stress the wall.
What to do instead:
- Use a free-draining granular material such as crushed rock or coarse sand as your primary backfill
- Compact backfill in layers (no more than 200mm lifts at a time) using a plate compactor
- Don’t over-compact directly behind the wall as this can push blocks out of alignment
- Keep expansive clays well back from the wall face
Taking the time to source and place the right backfill pays dividends in the life of the wall.
Mistake 7: Rushing the Cap Course and Finishing
The top of the wall is what everyone sees, but it also plays a structural role. Skipping a proper cap course or poorly fixing a cap can cause the top course to be displaced by foot traffic, mowing, or simply by time and weather.
Some installers also rush the final grading and landscaping around the wall, leaving areas where water can pool and direct runoff toward rather than away from the wall.
What to do instead:
- Use adhesive cap blocks or purpose-built coping designed for your block system
- Secure cap blocks with construction adhesive as specified by the manufacturer
- Ensure finished landscaping grades water away from the wall
- Allow for a drainage outlet point and verify it’s functioning before completing the job
A finished wall that manages water properly will look better and last longer with minimal ongoing maintenance.
Build It Right the First Time
Retaining wall mistakes are expensive to fix and sometimes impossible to hide. The good news is that every one of the errors listed above is entirely preventable with the right products, the right preparation, and a bit of know-how.
Starting with quality block systems designed and tested for Australian conditions is the foundation of a wall that lasts. The Retaining Wall Company offers a range of engineered retaining wall blocks built to perform, backed by the technical support to help get your project right from the ground up.
Call 0412 812 819 to speak to our retaining wall experts and discuss options to suit your home’s needs.
Frequently Asked Questions
How deep should the base of a retaining wall be?
For most residential retaining wall blocks, the base course should be buried at least 100mm to 150mm below finished ground level. For taller walls, increase this depth accordingly. Always compact the base material before laying the first course.
Do retaining walls need drainage behind them?
Yes, always. Without proper drainage behind the wall, hydrostatic pressure from trapped water will eventually cause the wall to lean, crack, or collapse. A drainage aggregate layer and ag pipe are essential components of any retaining wall build.
What height retaining wall requires council approval in Australia?
This varies by state and council, but most local governments require permits for walls over 600mm to 1 metre in height. Always check with your local council before starting. Walls adjacent to boundaries or below structures may have additional requirements.
Can I use any soil as backfill behind a retaining wall?
No. Clay-heavy soils retain water and can swell, creating excessive pressure on the wall. Use free-draining granular material such as crushed rock or coarse sand, compacted in layers, as your backfill material.
What causes retaining walls to lean or fail?
The most common causes are inadequate drainage (hydrostatic pressure), insufficient base preparation, walls built too high without engineering, and poor quality or incorrect backfill material. Most failures are preventable with correct installation from the start.
Do I need a professional to install retaining wall blocks?
For walls under 600mm, a capable DIYer with the right materials and knowledge can achieve a solid result. For anything taller, on steep slopes, near boundaries, or supporting structures, it’s strongly recommended to engage a licensed professional and seek engineering input where required.